Pond Pump

Pond Pump

High water flow
Energy efficient and internal use
Directional vortex impeller
Fountain head kits included
Thermally protected
Encapsulated pre-filter

Specifications：

Item no.	Flow rate	max. head	wattage	UPC # 0069037
BH 1000AD	342 GPH	3.93 ft.	7.5 w	2941 3
BH 2000AD	600 GPH	4.92 ft.	20 w	2942 0
BH 4000AD	1105 GPH	8.53 ft.	46 w	TBA
BH 6000AD	1579 GPH	10.17 ft.	74 w	TBA

Parts：

BH 1000AD

Three tier head
Two tier head
Fountain head uplift
Tube adapter
Water bell head
Fountain head adapter
Uplift tubes
Valve & water diverter
Diverter cap
Pump strainer
Impeller cover
Impeller
Pump
Additional pre-filter
Additional pre-filter bracket
Main pre-filter
Clasp

BH 2000AD：

Water bell head
Dual tier head
Three tier head
Uplift tube
Uplift tube coupler
Valve & water diverter
Diverter cap
Barbed pipe adapter
Pump strainer
Impeller cover
Impeller
Pump
Additional pre-filter
Additional pre-filter bracket
Main pre-filter
Clasp

Installation：

Open both, front and back clasps.
See diagrams 1.1 and 1.2.
Now, open the main pre-filter.
Connect the additional pre-filter to the main pre-filter. See diagram 2.
Close the main pre-filter.
Close and secure both clasps.
See part list diagrams for model BH-1000AD and BH-2000AD fountain head installation.
There are different options of the fountain head. Choose the appropiate setting depending on the application.
Place the pump in desired location. If pump is placed in a pond, raise the pump off the bottom of the pond by a minimum of 6 inches.
Start the ViaAqua® Pond Pump.

Maintenance：

If the water flow decreases, it’s a clear sign that debris is in the impeller or the pre-filter is clogged. It is the hobbyist’s sole responsability to ensure the pump is maintained frequently. Failure to properly maintain the pump will cause premature damage to the ViaAqua® Pond Pump.
Recommended routine maintenance: every 30 days.

Disconnect the pump from the GFCI (Ground Fault Circuit Interrupter) power supply prior to removing the pump from the water.
Open both, front and back clasps.
Remove the pump from the main pre-filter.
Clean the main and additional pre-filter.
Remove the impeller well cover.
Once the impeller well cover is removed, slide both the impeller and shaft out of the main body of the pump, and clean it well.
Verify the impeller is free of all dirt and debris.
Note: Do not use any soap or detergent during cleaning.
Once the impeller and shaft are cleaned, use a small brush to clean inside the motor housing.
Place the impeller back into the pump.
Reassemble above parts and your ViaAqua® Pond Pump is ready to use. Note: All washer and bushing must be reassembled properly. Failure to do so will cause permanent damage to the pump.
Insert the pump back to the main pre-filter. Attach additional pre-filter and start the ViaAqua® Pond Pump.

MAECENAS IACULIS

Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.

ADIPISCING CONVALLIS BULUM

Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
Diam parturient dictumst parturient scelerisque nibh lectus.

Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.